Jump to content

Motorcycles

Sign in to follow this  
27 topics in this forum
 
    • 1 reply
    • 1,609 views
    • 0 replies
    • 604 views
  1. Look what I got!

    • 0 replies
    • 1,314 views
  2. 75 cb750 tic

    • 5 replies
    • 783 views
  3. 1972 Suzuki TS 185 1 2

    • 29 replies
    • 4,388 views
  4. Kx125 headlight

    • 0 replies
    • 819 views
    • 24 replies
    • 1,439 views
  5. 1988 KX125

    • 3 replies
    • 631 views
  6. 2022 Beta 500rrs

    • 4 replies
    • 662 views
    • 8 replies
    • 900 views
  7. 2003 XR400R

    • 7 replies
    • 1,881 views
    • 55 replies
    • 8,429 views
  8. 1990 Suzuki FA50

    • 4 replies
    • 1,044 views
    • 7 replies
    • 1,656 views
  9. Honda Scooters

    • 1 reply
    • 1,354 views
    • 3 replies
    • 948 views
  10. New mule

    • 6 replies
    • 1,622 views
  11. 2004 GasGas EC Rookie

    • 6 replies
    • 1,832 views
  12. Letting go...

    • 1 reply
    • 978 views
  13. 1985 vf700c magna 1 2

    • 39 replies
    • 3,819 views
  14. my babies !

    • 14 replies
    • 2,480 views
    • 7 replies
    • 1,784 views
  15. Mini bikes

    • 6 replies
    • 1,886 views
  16. honda 300

    • 14 replies
    • 2,183 views
  17. 1987 vf700c magna

    • 0 replies
    • 1,004 views
 
Sign in to follow this  
  • Recent Posts

    • EDIT (Sorry I was not clear if you replaced CDI, I now see you had said ignition control module earlier)   Here ""wack a mole way, but worth a shot Try rapping pretty good on CDI with with handle of screwdriver or similar  while cranking, if you get an intermittent spark then you most likely have faulty CDI due to bad/craked internal solder joints,you  might get away with baking CDI @ 450 for 7-8 minutes Let us know -AKATV
    • I was kind of thinking the same- might just be a carb thing, as he said it runs fine with choke on and THEN clunks when you take it off choke Could just be struggling to run at low rpm and not clunking/slapping- but "described" sounds are different for everyone, so its hard to tell Might try turning idle up like Jeep said,, check or clean enrichment valve(choke) and make sure rubber boot under top cover of carb is not pinched if it has a throttle response hesitation. -Maybe post a video of it to better interpret sounds/issues -AKATV  
    • I was thinking it might be idling a little low so i will turn the throttle up some. I bought some fuel system cleaner is that worth putting in? I took the carburetor off and looked at it and it seemed clean to me no sludge or anything sticking. When I got it the man said that he had the carb cleaned and everything maybe he didn't fine tune it. I went to a 4wheeler mechanic and he said that the carb sounded like it needed to be looked at because there was a little hesitation in the throttle. I will look up were the stator is and check the voltage to see if that is correct. No it doesn't smoke at all never has. Thanks for your advice i Iike having someone with knowledge around that can help me learn. 
    • Noise could be something as simple as valves needing adjustment.  Idle might be low or have a dirty carb rather than need engine work.   More than likely you’re right, but might be a simpler fix. 
    • So at this point I'm torn. After checking for peak voltage at the coil and only getting 5v and 100v min, then at the ICM plug i had .52v with a min of .7 and then at the 5p generator plug I had .75v with 0.7 v min. I'm just barely at the bottom threshold at the generator plug. I'm having a hard time thinking it's a bad wire in the harness but I'm open to ideas... what's your thoughts?
×
×
  • Create New...