Leaderboard

here's good looking honda 3 wheeler.

I don't know if it's that bad inside, but I know my dexterity is too poor (nearly nonexistent) to be able to rebuild it. And the patience of my family members who have dexterity is also non-existent. So plopping in a new starter is our best option.

Wet in the ohio valley. a bit cool for this time of year. had a frost a couple a days ago. wonder if it will snow on Derby Day, 1st. saterday in may. wouldnt be the fist time. none of the horses running will be wearing snow shoes, this time. global warming, they dont sell them anymore.

some pics of maple syrup boil down, ran 4 weekends and made 73 pints in total for this year!

Ive had a couple, they seem to be getting few & far between now 😮

Is your starter that bad that you can't rebuild it?

its a gamble when buying from ebay, over half the sellers on there sell the wrong parts, but '' claim '' it will fit..lol. you better know what you are looking at/for when it comes to buying on ebay !. also, when buying oem parts ?, ALWAYS CHECK RMATV OR PARTZILLA FOR A LOWER PRICE ?!, i've seen sellers on ebay selling meters/displays at a higher price than from rmatv or partzilla, rmatv is where i buy my honda parts.

DB Electrical.com https://www.dbelectrical.com/

https://www.dirtbikes.com/honda-cr500r/ Honda produced them from the mid 1980's up until 2001. One of the most iconic mx bikes of all time!

we have another front just about to move in, jeep i think your correct this might be a back building large size front...... so far not warnings or watches out, and not a word from MTEARS.

Rain forecast here the next 3 days. I've gotten the water level way down in my duck hole, but not soon enough. The lilly pad shoots have already come up. Hopefully it will dry out quickly enough to kill them before they shade out the ground where other stuff (that ducks eat) can grow. But I'll be out busting out beaver dams again after all this rain moves through.

keep this in mind for future reference, there will be a time when a one-way bearing for your model will discontinue one side or the other ?, not a problem !. simply buy the side that still can be bought, flip the bearings around, use it on the bad side !.

yeah...... goofy me was washing cloths, and soaking my feet, having coffee, and my morning health drink, it just plain slipped my mind, one of the DOH moments, thank you for posting it up. Edit: I've got rain on my mind too...... i could use a ovwrvast day with light rain lightening and thunder, helps me relax, I'm still very stressed over the last few months.

this morning 60 degrees out slightly windy, the bar is holding steady..... MTEARS did mention a slight chance of severe weather later on on, so i did most of my shopping yesterday...... have we seen the last of winter ? possibly.

I'm hitting the 6000km mark with my 17.

I prepped the ES system in my 04 TRX350ES today following Retros directions. There was barely any grease on the reduction gears and what was there were dried clumps of crap! I took off all the plastics and went through entire harness and cleaned all connections and applied dielectric grease to them. I got the rear plastics back on and will finish putting the front plastics back on tomorrow. Many thanks to @retro for his thread on how to properly prep the ES system! My cousin dropped off his 08 Foreman 500ES today that is throwing angle sensor codes, so that will be next one on the lift for a thorough ES system prep.

We might set a record today , 90F is the record , they say we are going to be at least 88F , then a little cold snap thru the weekend , like 49F in the morning >>>>>> BRRRRRRRR !!!!! And I thought winter was over , LOL

That's easy with the softwood he's splitting in the video. I'd like to see him with a 20" yellow birch, or some rock maple. 🤣🤣🤣