-
Content Count
843 -
Joined
-
Last visited
-
Days Won
3
Melatv last won the day on April 23
Melatv had the most liked content!
Community Reputation
789 ExcellentPersonal Information
-
Location
Saint John NB Canada
The recent visitors block is disabled and is not being shown to other users.
-
Melatv started following Please name this part
-
Hi @Kyle9076 I would say it's the capacitor for the pull start -- just unplug it -- tape it up good and plug it back together
-
Hi @Mach 1: Just blow any dirt out of the connectors and put some dielectric grease around the edges of the connectors (NOT ON THE PINS)
-
@Mach 1 just info -- The CKP (crankshaft position sensor) send a 0.7 VAC (using PVA to test) to the PCM (ECM) -- then the PCM send a pulse to G/Y wire on the Ign. Coil to only pulse it to ground to fire the spark plug. Now with the PCM (ECM) being bad – which was holding the ground on the Ign. Coil (G/Y) wire for ever causing it heat up and damage it. That G/Y wire should away read infinity when not running the atv.
-
No spark, 2013 500 Foreman ES (now not fixed again)
Melatv replied to jeepwm69's topic in Electronics
@jeepwm69 -- I like your way you doing things -- stick with it -- try and try -- ending up solving the problem. -
Hi -- The green/yellow should read infinity -- that wire is pulled to ground by the PCM -- unplug the Gray 33P connector from the PCM -- unplug the Green/yellow wire on the coil and check that wire for continuity of that wire to ground -- it should read infinity -- if it does the PCM is at fault.
-
HI @Green Bay Mike -- are touching the gas lever when starting -- if so don't
-
What is cause of the gouges on the fly wheel ? must be loose metal some where
-
No spark, 2013 500 Foreman ES (now not fixed again)
Melatv replied to jeepwm69's topic in Electronics
HI @retro & @jeepwm69 I would un tape everything around that solder connector -- make everything right and try it. If still a problem then ECM or other things are the problem. The harness is a good deal if the person is willing to buy it first without cost to you. -
No spark, 2013 500 Foreman ES (now not fixed again)
Melatv replied to jeepwm69's topic in Electronics
Hi -- the wires with just the insulation covering just chew off -- use Permatex Liquid Electrical Tape -- I don't like using those heat shrink tubes with solder in them -- because the wires have to be perfectly clean -- solder the connections tape them good -or use crimped connectors and liquid tape the ends. -
No spark, 2013 500 Foreman ES (now not fixed again)
Melatv replied to jeepwm69's topic in Electronics
I see chewed wires there and other things that would cause the problem -- @retro good to find time to help out. -
No spark, 2013 500 Foreman ES (now not fixed again)
Melatv replied to jeepwm69's topic in Electronics
Yes -
No spark, 2013 500 Foreman ES (now not fixed again)
Melatv replied to jeepwm69's topic in Electronics
Do this again and let me know -
No spark, 2013 500 Foreman ES (now not fixed again)
Melatv replied to jeepwm69's topic in Electronics
Okay -
No spark, 2013 500 Foreman ES (now not fixed again)
Melatv replied to jeepwm69's topic in Electronics
Unplug the green connector (14pin) going to the display meter --see if voltage goes up -
No spark, 2013 500 Foreman ES (now not fixed again)
Melatv replied to jeepwm69's topic in Electronics
With black meter lead on neg of battery -- check the voltage on each little gray dot on top of ign. fuse