Jump to content
riverc

Light Bulbs

Recommended Posts

8 hours ago, _Wilson_™ said:

Looking good! Do you have the rear tail light assemblies too ? And i think ? Those rubber (right hand side from the pic) trunk rack straps might be upside down ? Pointing up... mine laid flat ... Looking at that bike sure does bring back memories of the great times i had riding my 85 250.....  N, Your back tire choice (i like) i had wooly boogers on mine... 

 

Thank you sir. I was able to get the front plastic carrier/rack on yesterday as well (mostly). Starting to look like a quad again! I do have the tail light assemblies, they're over on the bench right now. I've ordered LED replacement bulbs for them, once I get the bulbs I will reinstall the housings. And I'll look over the rubber rack straps but I'm pretty sure they way they are is the only way they'll go on and work to latch the door in place.

 

PXL_20230207_230905464.jpg

PXL_20230207_230854866.jpg

PXL_20230207_230848059.jpg

  • Like 2

Share this post


Link to post
Share on other sites
 
4 hours ago, Fishfiles said:

Looks right to me .


Hey Fish, good morning sir. Hey maybe you missed it in my last reply to you but do you by any chance remember the vendor/place where you picked up your Cree light bars?  Thanks!

  • Like 1

Share this post


Link to post
Share on other sites
 
12 minutes ago, Six862m6 said:


Hey Fish, good morning sir. Hey maybe you missed it in my last reply to you but do you by any chance remember the vendor/place where you picked up your Cree light bars?  Thanks!

I bought them all off of e-bay ,  I didn't pay much attention to the vender , except that they had a good reputation >>>>   over the years I have bought quite a few , they use to be cheap , about $20 or so , just looked and most are $60-80 and up , did see this one cheap and free freight

 

 108w 17 inch Cree $26.40 free shipping 

 

https://www.ebay.com/itm/383585727055?hash=item594f7db24f:g:ZRAAAOSwc49Y7HxW&amdata=enc%3AAQAHAAAA8IwT8wG65%2FlH5UJYAr76GLzYJzawSxsJyMVlJSVDjApr%2FEhh5NKmhkDEHDQSTcMaGCpJopawlk%2BTiyxdLTjwcckKb2guEPP5uyJFY%2FfpSid9DGi%2Bv%2BtvNi6tR82Yu19Dmf0ZVM5t9OtEqfjahkAXI5ixAbSTEBwaHPuL%2FZ20j9V9wtgnUBZ8QZDJ9SR3hcytuKvFpBMf8J6H01UxmVAjcPYShvbFYWZgd89ZEgTfzEEe4Mi8w0B9Pmsh%2Fe5nDpOhZ%2BCYk5JySWUivI4%2FApxJGnbr3k4UcETVu3tnMjcduDPAdvkDu%2F4Ai9era%2FeE%2FP2dpA%3D%3D|tkp%3ABFBM-Mb0kcZh

 

Share this post


Link to post
Share on other sites
 
13 minutes ago, Fishfiles said:

I bought them all off of e-bay ,  I didn't pay much attention to the vender , except that they had a good reputation >>>>   over the years I have bought quite a few , they use to be cheap , about $20 or so , just looked and most are $60-80 and up , did see this one cheap and free freight

 

 108w 17 inch Cree $26.40 free shipping 

 

https://www.ebay.com/itm/383585727055?hash=item594f7db24f:g:ZRAAAOSwc49Y7HxW&amdata=enc%3AAQAHAAAA8IwT8wG65%2FlH5UJYAr76GLzYJzawSxsJyMVlJSVDjApr%2FEhh5NKmhkDEHDQSTcMaGCpJopawlk%2BTiyxdLTjwcckKb2guEPP5uyJFY%2FfpSid9DGi%2Bv%2BtvNi6tR82Yu19Dmf0ZVM5t9OtEqfjahkAXI5ixAbSTEBwaHPuL%2FZ20j9V9wtgnUBZ8QZDJ9SR3hcytuKvFpBMf8J6H01UxmVAjcPYShvbFYWZgd89ZEgTfzEEe4Mi8w0B9Pmsh%2Fe5nDpOhZ%2BCYk5JySWUivI4%2FApxJGnbr3k4UcETVu3tnMjcduDPAdvkDu%2F4Ai9era%2FeE%2FP2dpA%3D%3D|tkp%3ABFBM-Mb0kcZh

 

Got it, thanks again for the info!

Share this post


Link to post
Share on other sites
 

I could be wrong.... I was told they were spose to point up...... But being OCD ... I put mine on.... Upside down i recon ? ... Just looks better to me.. Is all...

Share this post


Link to post
Share on other sites
 

I gotta say that's one of the best looking 250's I've seen in a while.... I mean it looks GOOD! .... n, I see part of a very nice looking chevy or gmc ? Truck.... 67 model ? C or K ?

Share this post


Link to post
Share on other sites
 
9 hours ago, _Wilson_™ said:

I gotta say that's one of the best looking 250's I've seen in a while.... I mean it looks GOOD! .... n, I see part of a very nice looking chevy or gmc ? Truck.... 67 model ? C or K ?


Appreciate it sir. I'll take some good pics of it and post them once it's truly done. Be around another month I'd say, just depends on the powder coater and how long they take with it's wheels.

As for the truck, good eye. That's my '68 GMC C15. 400 SBC in it from a '74 Impala. I've had her going on 15 years now..... Heres a good pic of it (parked next to my wife's '72 Cutlass):

 

IMG_20190608_142252.jpg

  • Like 1

Share this post


Link to post
Share on other sites
 

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now

×
×
  • Create New...