AKATV 839 Posted July 20, 2023 (edited) Look for an incoming message from Rdbrown4338 on his 02 Rancher trx350TE This is a Customers machine for him and I was hoping we could help get this straight for him No power to shift motor after starter was replaced-not sure if this was root cause Been thru the manual on this one with member and he is doing excellent troubleshooting Need a second, third, fourth... set of eyes Gut tells me something simple overlooked He has new OEM ECM (348.00) on hand and a second working Rancher ES to help with testing He has a lengthy writeup coming Probably need to start from scratch Edited July 20, 2023 by AKATV Share this post Link to post Share on other sites
Rdbrown4338 2 Posted July 20, 2023 I have a 2002 Honda TRX 350 TE 2WD with electric shift that will not shift. I have downloaded the Honda service manual and printed out the pages needed. Following the flowcharts provided by Honda I will discuss the things that I have tried to fix this bike. I’m also communicating with AKATV on this forum for help. Starting off, the Batt is fully charged and there are no fuses blown. And 12V to all places coming out of the fusebox. The clutch is properly adjusted. I can shift the bike manually with the tool to each gear needed. On the display it will show the correct gear position that is selected. Next test is to check for voltage on the Black/Green wire at the connector at the ECU to ground with the switch turned ON. There is 12V to ground at this wire. Next test completed was to disconnect the Brown Connector at the ECU. Then measure the voltage between the Red/Yellow + terminal of the harness and ground – with switch turned on. There was 12V there with switch on or off. Because it comes directly from the Batt/Fuse. Next test. Is to test between the Green wire at the Brown connector to Ground-.which showed good connectivity to ground-. Next was to test the resistance at ECU connector for the angle sensor. Which was 4.6ohms. Next test was to remove the angle sensor and visually inspect. Everything was in perfect condition. Resistance the same there, 4.6ohms. Then checked the input voltage at the angle sensor plug, it was 5V. Next test is to test the continuity of the gearshift switch which is done at the front connector under the front fenders. The standard voltage form the Black/Red wire is 5.0V as recommended. The continuity between the White Blue wire and the Red/Black when the UP switch is pressed is perfect. The continuity between the White/Yellow wire and the Red/Black is perfect also. These connections were checked at the connector 10P under the fenders and also at the connector at the ECU 22P. all were normal and had 5V going into the switch at 5V. And when backprobed at the ECU connector the 5V would be put to the up/down switch wires, white/blue –black red and white/yellow-black red. So continuity and voltage both to and from the GEARSHIFT SWITCH are all normal. Next test is to test the GEAR POSITION SWITCH located in the rear housing of the engine by checking continuity between all wires going to that switch from connector 22P the ECU connector and the 8P going from the GEAR POSITION SWITCH Each terminal needed to be tested to ground at certain gear positions. Neutral=light green/red to ground. Good ground. Reverse=gray to ground. Good also. 1st=white/green to ground. Good ground. 2nd= white/red to ground. Good ground. 3rd=blue to ground. Also good ground. 4th= yellow to ground. Good ground. 5th= light blue/white to ground. Good ground. Next test is to check continuity between the 2P connector connecting the Shift motor and the 5P connector at the ECU. All good there too. Next test is to remove shift motor and bench test by applying 12V directly to the motor. It ran as smooth as possible. And by reversing the wires would run backwards also. After that the next step from the service manual is to replace the ECU/change shift unit. Which I did, and no change to no shift condition. I have a 2006 Honda TRX 350 Electric Shift also, so I swapped the known good ECU into the 2002. still no shift. So by trying 3 different ECUs it is not that causing the trouble. I also swapped the angle sensor from the 06 to see if that worked too, still no shift. Both part numbers are the same for the ECU and the Angle Sensor for the 2002 and the 2006. I also installed a new GEAR POSITION SWITCH just to be sure and still no difference. So I’m stuck with a $380 ecu. Next I checked the speedometer sensor and cleaned it. Measured voltage between black/blue + and green-. Which produced 5V. and the speedometer registers at the display by turning the tires. All gear positions are displayed correctly when manually shifted from gear to gear.even reverse. Pin fitment has all been checked on every connection by back probing. The motor runs good and the shift gears have been cleaned up and re greased.Just cant get any voltage to it. All fuses and power to red?black are good. Recap ECU swapped with good/known Angle sensor swapped with good/known Shift motor bench tested with 12V good. All gears show exactly where they are. Speed sensor works and displays speed. This thing has got me throwing tools! I need some help. Honda techs around here know nothing. And wont even work on it. Share this post Link to post Share on other sites
AKATV 839 Posted July 20, 2023 One thing I forgot to ask earlier is if you follow the flow chart starting from the beginning in the manual what is the first failure point that you hit? l I guess the biggest mystery so far is we know that we have no power going to the shift motor but so far everything is checked out which is actually impossible because obviously we have a failure somewhere Let’s let’s start at the beginning and work through until we hit the first failure or questionable part as per the manual and take it from there Share this post Link to post Share on other sites
Rdbrown4338 2 Posted July 21, 2023 I will run through it again in the morning to double check. Share this post Link to post Share on other sites
ATC4ever 1,084 Posted July 21, 2023 Thats a lot to read over 😮 Forgive me if i missed something. But you say the starter was replaced & THEN it started doing this? Share this post Link to post Share on other sites