Melatv 797 Posted August 14 Hi @struthers unplug the ign. switch and put jumpers on the harness side of the connector Red to Pink and Red to Black 1 Share this post Link to post Share on other sites
struthers 4 Posted August 14 @Melatv okay jumpers as in just spare wires or what? And plug it into the battery? Share this post Link to post Share on other sites
Melatv 797 Posted August 14 Don't do nothing with the battery -- just unplug the key switch and put jumpers in place -- R to P and R to BL Share this post Link to post Share on other sites
struthers 4 Posted August 14 @Melatv okay where am I putting these jumper wires when I connect them in Share this post Link to post Share on other sites
struthers 4 Posted August 14 @Melatv nevermind I see what your saying to do my apologies, what will this do when i do this? Share this post Link to post Share on other sites
struthers 4 Posted August 14 @Melatv okay I have the jumped now what? Share this post Link to post Share on other sites
struthers 4 Posted August 14 @Melatv I've lost all power to the atv nothing shows to be on when key is on and cant turn it over from start button either. Share this post Link to post Share on other sites
Melatv 797 Posted August 14 Check the fuse again -- don't pull the fuse out -- put the black meter lead on neg. of battery -- check the fuses by touching the red meter lead on the little gray dot on top of the fuses Share this post Link to post Share on other sites
struthers 4 Posted August 14 @Melatv okay checked the 10 amp ign fuse just like you said to and I'm not getting anything there with key on or off Share this post Link to post Share on other sites
Melatv 797 Posted August 14 You have to have the key switch unplugged and jumpers in place on the connector side going to harness on the bike Share this post Link to post Share on other sites
struthers 4 Posted August 14 @Melatv yes that's the way I have it switch is unplugged and jumpers are installed and I'm getting nothing at that ign fuse. Share this post Link to post Share on other sites
Melatv 797 Posted August 14 Do you have 12 DC on the top of the 30 amp main fuse? Share this post Link to post Share on other sites
struthers 4 Posted August 14 @Melatv yes on both of the 30amps I have over 12 volts Share this post Link to post Share on other sites
Melatv 797 Posted August 14 It looks like jumpers you put on are not making contact Share this post Link to post Share on other sites
struthers 4 Posted August 14 @Melatv okay I'll double check, I back probed the connector, its unplugged but i just used back probes because its what i had Share this post Link to post Share on other sites
Melatv 797 Posted August 14 Those jumpers are on the connector side with the 2 Red wires - Pink & Black -- Check to see if have 12 vdc on red wire & black wire to ground of connector Share this post Link to post Share on other sites
struthers 4 Posted August 15 @Melatv okay I actually found some wire and made jumpers I'm getting power on now light come screen comes on, but it won't turn over from the start button. I am getting 11.44 volts now out of ignition fuse location, i got about 12 volts at the battery. Share this post Link to post Share on other sites
Melatv 797 Posted August 15 does the starter turn the engine over? Share this post Link to post Share on other sites
Melatv 797 Posted August 15 I am out of here for the night -- I will see if I can find time tomorrow Share this post Link to post Share on other sites
struthers 4 Posted August 15 @Melatv okay now it will work at the start button I tightened my connectors, it turns over at the start button, just still no spark. Share this post Link to post Share on other sites
jeepwm69 7,731 Posted August 15 15 hours ago, struthers said: @Melatv okay I actually found some wire and made jumpers I'm getting power on now light come screen comes on, but it won't turn over from the start button. I am getting 11.44 volts now out of ignition fuse location, i got about 12 volts at the battery. I'm going to hope Mel comes back today, but he's bypassing your ignition key switch to see if you have a problem in the switch itself. Share this post Link to post Share on other sites
Melatv 797 Posted August 16 (edited) Back home-- @struthers lets start with ign. coil -- remove the Bl/Y wire from the ign. coil -- put your meter on the lowest ohm scale and check the ohms of the primary side of the ign. coil -- should read around 0.1 - 2 ohms Also check ohms on the Green wire to ground --should read zero Edited August 16 by Melatv Share this post Link to post Share on other sites
struthers 4 Posted August 16 @Melatv okay I'm getting 0.2 ohms Share this post Link to post Share on other sites
struthers 4 Posted August 16 @Melatv from the green wire to the negative battery post I get .3 ohms Share this post Link to post Share on other sites