Orvis25 108 Posted July 1, 2021 Repost of my old forum thread on prior website ______________________________________ Hey Guys! So as promised to @shadetree, I made a tutorial (as there is not one on this forum, or on the internet that I can find) in appreciation of him helping me figure out how to make this tool (much simpler then the plans i was making to remove it). So here we go! Quick video showing / Explaining how it works: Parts: 1) 1 1/2 x 1 1/2 in square metal tube 2) Metal file 3) Pipe Wrench Optional (only if need): 1) large Flat piece of metal 2) drill How to make it! Step 1) Take your metal tube and file around the tube gently so it is much smother (can also use sandpaper afterward if you want even smother) Step 2) Insert into the 60mm lock nut (P/N: 90244-HA0-000) and turn Counterclockwise Step 3)Remove the lock nut from differential housing, and pull out the pinion and bearing Step 3) This is the most important... Send me some money for beer!!! AND THERE YA GO! YOUR DONE! To install it, just literally do this in reverse! For the optional tool, all I can say is to do this: Step 1) Take a piece of cardboard. Place some grease on the tips of the 4 bolts sticking out of the differential, and press the cardboard to them to stain it were the bolts are. Step 2) Place the cardboard over the flat piece of metal, and drill out the 4 bolt holed through the cardboard. Step 3) Cut a 2" hole in the center of the 4 bolts on the flat metal Step 4) take a piece of scarp metal and weld it to the bottom of the flat metal so it can be placed in a vice And your done! If this helped please thumb up my video and say thanks! Happy Repairing guys! Edit: A tip on taking the pinion nut off: * this tip should allow to skip buying the pinion holder tool 07924-HA00001* Here is what i did. I took a vice (with rubber grips, but just put something like a few rubber bands in there so it wont get scratched up, and sticks better), and with the side panel off the differential (exposing the ring gear) i put part of the tube that comes out of the ring gear (were rear axle goes through) in the vice and clamped it down. That way the pinion wont rotate because the ring gearl is holding it stationary (if one turns, the other turn's). Now you can take that pinion bolt off freely without the need of that $120 tool ! 6 Share this post Link to post Share on other sites
shadetree 5,969 Posted July 1, 2021 nice !, well done :-). 2 Share this post Link to post Share on other sites
Orvis25 108 Posted July 1, 2021 Just now, shadetree said: nice !, well done :-). Heyyyyy, Good to see you again brother. Thanks 😛 Share this post Link to post Share on other sites
shadetree 5,969 Posted July 1, 2021 6 minutes ago, Orvis25 said: Heyyyyy, Good to see you again brother. Thanks 😛 yw, you should know, no one can keep a good honda mechanic away from honda's !..lol i tried to leave here awhile back, retro would not have any of it ?..hmmm..i guess he knows skill when he see's it ?..lol. 2 Share this post Link to post Share on other sites
Orvis25 108 Posted July 2, 2021 3 hours ago, shadetree said: yw, you should know, no one can keep a good honda mechanic away from honda's !..lol i tried to leave here awhile back, retro would not have any of it ?..hmmm..i guess he knows skill when he see's it ?..lol. "leave here" Like retire from honda forums altogether? Id miss ya :{ Share this post Link to post Share on other sites
Wheeler 2,527 Posted July 2, 2021 Hahaha AWESOME. I made one two years ago myself when I re did my rear diff!! 1 Share this post Link to post Share on other sites
shadetree 5,969 Posted July 2, 2021 3 hours ago, Orvis25 said: "leave here" Like retire from honda forums altogether? Id miss ya :{ haha..i'm not going anywhere....yet !..lol. 1 Share this post Link to post Share on other sites
Orvis25 108 Posted July 2, 2021 (edited) 29 minutes ago, shadetree said: haha..i'm not going anywhere....yet !..lol. well your but better PM me a goodbye, even if i take another hiatus from the forum for whatever reason (most likely life). known you almost 9 years now Edited July 2, 2021 by Orvis25 1 Share this post Link to post Share on other sites
Orvis25 108 Posted July 2, 2021 3 hours ago, Wheeler said: Hahaha AWESOME. I made one two years ago myself when I re did my rear diff!! Cheers 🙂 1 Share this post Link to post Share on other sites
jeepwm69 7,719 Posted July 2, 2021 10 hours ago, shadetree said: haha..i'm not going anywhere....yet !..lol. Shade goes off and does "real life stuff" occasionally. But he likes helping folks out too much to stay away long...... 2 Share this post Link to post Share on other sites
_Wilson_™ 6,591 Posted July 2, 2021 yeah, for a while we thought he was going to be a traveling honda atv mechanics, helped a bunch of members out, if that's not dedication, and a friend, i dont what is. 2 Share this post Link to post Share on other sites