Popa Fry 62 Posted May 25, 2022 I have an engine tore apart for a rebuild. Previous owner had oil line brake Was not run much after .?? I am new to posting on a forum I tried once before receiced no replies it was for a different forum. I am sure I did something wrong or don't know where to see the replies. I am 71 years young and not that savvy . That said I have this motor tore apart completely and the case separated ( just a note I can rebuild and any car engine made.. but. new to ATV motors). the only thing I have found bad is the rod end where the wrist/piston pin attaches to the piston . It was galled so bad I had a lot of trouble removing it ..The motor is not locked up but there is no way to check the rod bearings as they are attached to the crank. There lies my Problem somewhat . I have tried to purchase a rebuild kit for a 2000 Honda TRX400FW Forman and They DO NOT Exist as for as I can tell. Please someone direct me to where I can get the crank and rod I even Tried e-bay knowing I could get had!! but there is not one to be found. if I don't find what I need all I have is a pile of junk.. I would like to get this fixed Any Help Appreciated. Thank you in advance for any help ( If someone on this forum has one I Will buy it ! Share this post Link to post Share on other sites
Fishfiles 20,147 Posted May 25, 2022 Welcome to ATVHonda --- you got me by 7 years Guys name is Vince http://www.mrcrankshaft.com/ Share this post Link to post Share on other sites
jeepwm69 7,719 Posted May 26, 2022 Welcome aboard. Vince at Mr Crankshaft will fix you right up, and is one of the rare instances where you get good, cheap, and fast. Post up any other questions you have. We like to talk Hondas, and will do our best to help you fix your rig up the best (and cheapest) way possible. Share this post Link to post Share on other sites
Popa Fry 62 Posted May 26, 2022 Thank you men so much I was at my wits end. His place is in Kentucky and I live in Georgetown Kentucky ... I will reach out to him today and will let you know what happens . Again Thanks I now have hope i will get this back together in the best possible condition. zny ideas where to get the most complete Gasket set would be nice if it contains all o rings and seals. Thanks. P.F.. 2 Share this post Link to post Share on other sites
Fishfiles 20,147 Posted May 26, 2022 I have never seen a gasket kit that contains all the seals , those seals you need will have to be bought individually from Honda ---- gasket kit I would go thru G+H Discount ATV https://www.ghdiscountatvsupply.com/quality-complete-full-gasket-kit-for-the-1995-2003-honda-trx-400-fourtrax-foreman-atvs/ Vince use to be able to upgrade you to a Vesrah connecting rod for a few dollars more , which is arguably an upgrade , ask him about that Share this post Link to post Share on other sites
Popa Fry 62 Posted May 26, 2022 Thank you i have now opened up a new resource for myself into ATV repair. It's nice to find people helping people . Maybe some day i will be able to help someone also. 2 Share this post Link to post Share on other sites
Fishfiles 20,147 Posted May 26, 2022 16 minutes ago, Popa Fry said: Thank you i have now opened up a new resource for myself into ATV repair. It's nice to find people helping people . Maybe some day i will be able to help someone also. True , we have a good group of people that hang out here on ATVHonda , even though we are from all different walks of life , ATVs are a common denominator and most are willing to help So what is your speciality in life ?? I am a heavy equipment mechanic / operator by trade .... I have a couple of 450s and 300s , do a little work with them around the house , most they are just for playing in the mud ..... what is your used for ??? Share this post Link to post Share on other sites
Popa Fry 62 Posted May 26, 2022 Hunting some light farming ...Retired mechanical Eng. CAD Designer.. I worked with father in automotive Garage . have rebuilt everything from 1964 235 straight line 6 cyl ( first one) and 4-6-8 Flat Head engines a Plymouth Race engine and one 570 Milk Truck engine all Gas engines. some service work on personal boat motors. ..Had small Kawaski 220 wanted something bigger found a Polaris 500 needed a lot of work but the engine was good when finished got an offer for $ 1000.00 profit ..Sold IT. Found good Honda rebuilt carb replaced rear axle and all rear brake components good little unit but i wanted a Honde 400 when i found one i could afford it has a blown engine Back to first post. 1 Share this post Link to post Share on other sites
Popa Fry 62 Posted May 26, 2022 update i talked to Vince at MrCrankshaft very friendly and helpful. The Price was more than expected $329.99 this includes up grade rod. but i look to ship it today Thanks Men... 1 Share this post Link to post Share on other sites
jeepwm69 7,719 Posted May 26, 2022 A lot cheaper (and better) than a new OEM crank. I think you’ll be really pleased with Vince’s work. He’s a good guy 2 Share this post Link to post Share on other sites
Goober 1,555 Posted May 29, 2022 (edited) Very good @Popa Fry. I saw ya posted over there and typically no one responds or they give half-assed advice. Serious wrenchers over here. Keep us updated PF! Edited May 29, 2022 by Goober 2 Share this post Link to post Share on other sites
Popa Fry 62 Posted May 29, 2022 I believe you are spot on. I will post final results ASAP Share this post Link to post Share on other sites
shadetree 5,969 Posted May 29, 2022 @pop fry , just some light info for future reference , a trx450fm/s/es crank is the same crank as the trx400fm !. 1 Share this post Link to post Share on other sites
Popa Fry 62 Posted May 30, 2022 i have been told that the lower 450 is basically the same with a different upper . Thanks Share this post Link to post Share on other sites
shadetree 5,969 Posted May 30, 2022 1 hour ago, Popa Fry said: i have been told that the lower 450 is basically the same with a different upper . Thanks you are correct. lower engine is the same, only thing they changed is the cylinder size, and the piston size. 1 Share this post Link to post Share on other sites
Fishfiles 20,147 Posted May 30, 2022 Another thing , the 450 and the 400 have different heads 1 Share this post Link to post Share on other sites
Popa Fry 62 Posted May 30, 2022 i have already reworked the head bore 86.22mm .22 mm over and faced the valves new piston everything looks great.. Thanks fo everyone's help it is appreciated. Share this post Link to post Share on other sites
_Wilson_™ 6,591 Posted May 31, 2022 Welcome to ATVH. Share this post Link to post Share on other sites
Popa Fry 62 Posted May 31, 2022 After this project i will be a LOT more knowledgeable than wen i started... lol 1 Share this post Link to post Share on other sites
shadetree 5,969 Posted May 31, 2022 44 minutes ago, Popa Fry said: After this project i will be a LOT more knowledgeable than wen i started... lol you are deff in great hands to learn from here !!. i started doing this 30 yrs ago, mostly self taught, it takes years to learn the skill of doing this kinda work. Share this post Link to post Share on other sites
Popa Fry 62 Posted June 1, 2022 working on auto engines gives me a great background . I do have one new question when putting the engine back together do you use any thing on the gaskets ?? someone suggested silicone but I don't like that idea . give me your thoughts Thanks.. Share this post Link to post Share on other sites
jeepwm69 7,719 Posted June 1, 2022 No. Gaskets stay dry. In some engines there is no gasket, and in that case you only use Hondabond or Yamabond On your 400 use gaskets, and leave them dry. I tried to get “extra sealing” using Hondabond and gaskets on the last one I did and just made a huge mess. Share this post Link to post Share on other sites
Popa Fry 62 Posted June 1, 2022 I believe i have the surfaces properly cleaned and i will put them on dry Thanks Share this post Link to post Share on other sites
shadetree 5,969 Posted June 1, 2022 48 minutes ago, Popa Fry said: I believe i have the surfaces properly cleaned and i will put them on dry Thanks install dry only !. just ask jeep ^^^ how that worked out...AFTER I TOLD HIM HOW TO DO IT ?!..LOL. 1 Share this post Link to post Share on other sites