Misterclean 421 Posted May 6, 2020 4 hours ago, SlammedRanger said: No worries bud! Im a good sport! Haha I've been riding dirt bikes for decades and never had a problem like this. Just a limit on the counter shaft sprocket before it hits the case. Share this post Link to post Share on other sites
TRX2FiveO 42 Posted May 6, 2020 3 hours ago, Misterclean said: I've been riding dirt bikes for decades and never had a problem like this. Just a limit on the counter shaft sprocket before it hits the case. 16 tooth w/ case saver.. not a glann but hey🤷🏻♂️ 1 Share this post Link to post Share on other sites
SlammedRanger 1,556 Posted May 7, 2020 1 hour ago, TRX2FiveO said: 16 tooth w/ case saver.. not a glann but hey🤷🏻♂️ I looked at the one you have. Im a big fan of the poly ones. The one i have now is a moose racing polymer one. If it fit a 15 tooth i would just stick with it. Glann sells a poly one that eliminates the lower chain roller and it actually fits over the shifter shaft to add support for that aswell. I plan to order there crf skid plate at the same time. Im about 20 bucks short of ordering them. Share this post Link to post Share on other sites
SlammedRanger 1,556 Posted May 11, 2020 So i took some videos for evidence that a 15/36 combo will 100% not work on my quad. I have a 37 tooth rear on order and a chain breaker/rivet tool so i can use a rivet type link where i added the link. To mainatain as much strength as i can. Uploading the videos to youtube and will post them asap. Stay tuned! 1 Share this post Link to post Share on other sites
TRX2FiveO 42 Posted May 11, 2020 2 hours ago, SlammedRanger said: Looks like you're removing more than 1 link dude. Not saying you're crazy !...Show me what you took out. Also with it all the way adjusted like that suspended its gonna have all of that slack. I've never ever ran into a quad needing an odd or even gear set. Share this post Link to post Share on other sites
SlammedRanger 1,556 Posted May 11, 2020 4 minutes ago, TRX2FiveO said: Looks like you're removing more than 1 link dude. Not saying you're crazy !...Show me what you took out. Also with it all the way adjusted like that suspended its gonna have all of that slack. I've never ever ran into a quad needing an odd or even gear set. I added 1 link. Didnt remove anything. Since i was going up from a 14 to a 15. The link i added was one skinny piece with 2 holes. And 1 wide piece with 2 pins. Cant add just one or you cant connect the 2 ends of chain. With it adjusted all the way tight and quad suspended i could make contact between the chain and swing arm 4 inches of up and down movement. Once i put it down on the ground i had about 3 inches of up and down on the chain. I have never ran into this before either. I have never had a quad i couldnt tighten the chain all the way tight and then loosen it so i had 1 1/4-1 5/8 inches deflection like the fsm says is what your supposed to have. 1 Share this post Link to post Share on other sites
TRX2FiveO 42 Posted May 12, 2020 Are you using a 400 chain or a 450r chain? Share this post Link to post Share on other sites
SlammedRanger 1,556 Posted May 12, 2020 This is the exact chain i used. Doesnt say 400ex or 450r. Its just a 520 chain. Share this post Link to post Share on other sites
retro 4,048 Posted May 12, 2020 The company who made that stretched swingarm screwed it up. Its too long by about 1/4" else your chain would have fit on the 1st attempt without adding a link. 2 Share this post Link to post Share on other sites
TRX2FiveO 42 Posted May 13, 2020 Count your links. You should of been able to buy a 450 chain 96 link that's 06-up 04-05 has 94 link Share this post Link to post Share on other sites
SlammedRanger 1,556 Posted May 13, 2020 I just buy rk chains, what ever is over 100 links and is the cheapest. As long as its a 520. This time i got a 116 link rk chain for 65.00. I know how to cut chains to length so ordering them in specific length doesnt really matter to me. There are non specific length chains to be had real cheap sometimes. Share this post Link to post Share on other sites
SlammedRanger 1,556 Posted May 18, 2020 ***Update*** If the rain ever stops here i can hopefully go test this gearing out. I did get the 15 tooth front sprocket on. The crf skid plate on. And the glann case saver. This is where i learned i shouldnt use my memory for things. So i had thought i was running a 14/36. I was actually running a 14/37. So i now have 2 brandnew 37 tooth sprockets for a 400ex if anyone wants one? LoL. Because with the 15 tooth front i cant use a 37 at all. So i installed my old 38 tooth i had since i spent all the time installing the rivet type master link in my chain already. The positive side. I can run a 15/36 if this 15/38 isnt enough gear. The negative side. Dont have a 36 tooth at all yet........its ordered now incase i need it. 3 Share this post Link to post Share on other sites
Wheeler 2,525 Posted May 18, 2020 I love this build... You make me want to run out & pick me up a 400ex! Hats off... 3 1 Share this post Link to post Share on other sites
SlammedRanger 1,556 Posted May 18, 2020 16 minutes ago, Wheeler said: I love this build... You make me want to run out & pick me up a 400ex! Hats off... Thanks man! Im just chomping at the bit to ride already. Still waiting on my lonestar steering stem also. Got to be really patient with ordering anything from them since they build to order. It was over a month ago i ordered it. But once i get that and install it i am done spending money. Hopefully time to go do some racing. 3 Share this post Link to post Share on other sites
SlammedRanger 1,556 Posted February 11, 2021 Well after banishing my quad to the mobile storage unit a.k.a the toyhauler lol. To work on a buddys polaris........ugh. I got it back in the garage and had some spare time to remove the shocks to send off to BNR for there freshen up treatment. And while i was at it i dropped the needle clip down one slot to see if it stopped the black smoke when revving on it. And all i can say is wow! It really likes that needle change. Cant wait for it to get warm so i can test ride it. But just revving in the garage it seems alot more crisp. And no more black smoke. I also didnt get a single comment from the wife or daughter about smelling like gas! So that seems like progress to me. LoL 6 Share this post Link to post Share on other sites
Jlodini36 0 Posted February 2, 2022 On 3/1/2020 at 8:30 PM, TRX2FiveO said: Here is my new intake. Before I did the final bore shaping Who made tbis piece Share this post Link to post Share on other sites
Fishfiles 20,145 Posted February 2, 2022 44 minutes ago, Jlodini36 said: Who made tbis piece The 12th of this month was the last time @TRX2FiveO logged in , I just hailed him for you , @SlammedRanger likely knows the answer to your question Share this post Link to post Share on other sites
Jlodini36 0 Posted February 2, 2022 22 minutes ago, Fishfiles said: The 12th of this month was the last time @TRX2FiveO logged in , I just hailed him for you , @SlammedRanger likely knows the answer to your question Your saying who knows the answer ? Share this post Link to post Share on other sites
Jlodini36 0 Posted February 2, 2022 14 minutes ago, Jlodini36 said: Your saying who knows the answer ? How do I get in touch with him Share this post Link to post Share on other sites
TRX2FiveO 42 Posted February 2, 2022 (edited) 1 hour ago, Jlodini36 said: Who made tbis piece Hey man. It's a piece I had made by Mike's Custom machine. I dont remember what it cost me? Jerry White is the only other one I know of that has ever made one . I'm sure other have. This one was made to fit my Lectron, which is considerably larger than a stock 400 carb. I'm easier to find on FB (Darryl Bennett) I'm on alot of 400 forums there. I dont think I'veever mentioned it to @SlammedRanger . @Fishfilesthanks for the heads-up. I not here much anymore. I should be but I'm not😬😂😂 1 hour ago, Jlodini36 said: Who made tbis piece Edited February 2, 2022 by TRX2FiveO 1 Share this post Link to post Share on other sites
Fishfiles 20,145 Posted February 2, 2022 56 minutes ago, TRX2FiveO said: Hey man. It's a piece I had made by Mike's Custom machine. I dont remember what it cost me? Jerry White is the only other one I know of that has ever made one . I'm sure other have. This one was made to fit my Lectron, which is considerably larger than a stock 400 carb. I'm easier to find on FB (Darryl Bennett) I'm on alot of 400 forums there. I dont think I'veever mentioned it to @SlammedRanger . @Fishfilesthanks for the heads-up. I not here much anymore. I should be but I'm not😬😂😂 Wow , That was amazing , I threw out a Hail Mary and you popped up 42 minutes later at 6:00AM in the morning ----- good to see you around , hope to see you more Share this post Link to post Share on other sites