slowindown 494 Posted May 25, 2020 That's nice!!! 1 Share this post Link to post Share on other sites
_Wilson_™ 6,567 Posted May 25, 2020 7 hours ago, Fishfiles said: WOW , Smithsonian Museum Quality !!! sure enough a collectors dream!! nice restor goober! 1 Share this post Link to post Share on other sites
jeepwm69 7,611 Posted May 26, 2020 No kidding Fish. That thing is pretty. 1 1 Share this post Link to post Share on other sites
retro 4,048 Posted May 26, 2020 Outstanding 350 Goober! WOW! 1 Share this post Link to post Share on other sites
Melatv 792 Posted May 27, 2020 Hi -- you done one great job doing it. 1 Share this post Link to post Share on other sites
Goober 1,555 Posted May 27, 2020 6 hours ago, retro said: Outstanding 350 Goober! WOW! That 2000F paint was really fighting to keep from bubbling but it’s still there! Thanks for recommending it! 1 Share this post Link to post Share on other sites
DuckOfDeath 98 Posted May 27, 2020 Great job, Goober. Looks fantastic! 1 Share this post Link to post Share on other sites
Goober 1,555 Posted May 28, 2020 17 hours ago, DuckOfDeath said: Great job, Goober. Looks fantastic! Thanks Duck—got yer old stator in it! Share this post Link to post Share on other sites
machinecrook 68 Posted June 3, 2020 Wow, mint condition. Good job! 2 Share this post Link to post Share on other sites
_Wilson_™ 6,567 Posted June 3, 2020 good to see you active again machinecrook .... it's about time some of the long time members show up :-) 2 Share this post Link to post Share on other sites
machinecrook 68 Posted June 4, 2020 19 hours ago, _Wilson_™ said: good to see you active again machinecrook .... it's about time some of the long time members show up 🙂 Haha yeah! This covid business had me very busy but work related things are getting a bit more back to normal. Heck I've barely been on my 4 wheeler or cut any wood in 3 months! 2 Share this post Link to post Share on other sites
Goober 1,555 Posted September 3, 2020 (edited) I bought an old Cycle Country manual lift kit for my Kolpin plow. It is part number 15-0015; the old part number 15-0010 will fit this quad but the drawbar is too short to clear the foot wells on newer quads. 15-0015 is called the extended manual lift kit—the draw bar is 2-3 inches wider than the 15-0010. the kit installs on a push tube assembly that is prepped for this type of manual lift. It will have a welded on flange and eyelet on the left side tube. So here is the installed kit on the plow assembly. i bought a set of NOS plow mounts for this old girl, too. Edited September 3, 2020 by Goober 4 Share this post Link to post Share on other sites
Goober 1,555 Posted December 12, 2021 i replaced the tie rod ends closest to the steering arm today. I got them pretty well aligned so I’ll drive it tomorrow and make final adjustments. Steering is still loose so I’ll look at changing the steering bushes. i found the lug nuts loose. Don’t know why maybe I didn’t torque them. I’m hoping that’s what was clicking. Maybe i can get it on the trail tomorrow. I found an original new CMP front cooler carrier for this old Fourtrax. And i put my old beat up Hondaline accessory bumper under it. i really like the look of it without the bumper and carrier—you know, the no-option look. Because now i have to install a headlight riser to see over the carrier. Well if i want to take it into the woods, I’ll probably want the carrier. 3 Share this post Link to post Share on other sites
shadetree 5,869 Posted December 13, 2021 On 12/11/2021 at 9:57 PM, Goober said: i replaced the tie rod ends closest to the steering arm today. I got them pretty well aligned so I’ll drive it tomorrow and make final adjustments. Steering is still loose so I’ll look at changing the steering bushes. i found the lug nuts loose. Don’t know why maybe I didn’t torque them. I’m hoping that’s what was clicking. Maybe i can get it on the trail tomorrow. I found an original new CMP front cooler carrier for this old Fourtrax. And i put my old beat up Hondaline accessory bumper under it. i really like the look of it without the bumper and carrier—you know, the no-option look. Because now i have to install a headlight riser to see over the carrier. Well if i want to take it into the woods, I’ll probably want the carrier. i have not checked to see if the steering bushings are discontinued lately ?, but i can tell you this, the upper bushing , if it is discontinued ?, do what i did, i took a bearing race that matched the outside dia, then used my dremel with a grinding stone, and made the inner dia to fit the steering shaft, yes..it took over an hour to grind it..because they are tempered..lol. but it was worth it..that steering bushing now will never wear out !..lol. as for the lower steering bushing bearing ?, same thing..not sure if its around as well ?. 3 Share this post Link to post Share on other sites
Fishfiles 20,145 Posted December 13, 2021 2 hours ago, shadetree said: i have not checked to see if the steering bushings are discontinued lately ?, but i can tell you this, the upper bushing , if it is discontinued ?, do what i did, i took a bearing race that matched the outside dia, then used my dremel with a grinding stone, and made the inner dia to fit the steering shaft, yes..it took over an hour to grind it..because they are tempered..lol. but it was worth it..that steering bushing now will never wear out !..lol. as for the lower steering bushing bearing ?, same thing..not sure if its around as well ?. I missed that steering bearing modification , sounds ike something I would like 2 Share this post Link to post Share on other sites
Goober 1,555 Posted December 13, 2021 I need to change those bushings because the steering is still loose. I did get the alignment set, though. Share this post Link to post Share on other sites
shadetree 5,869 Posted December 13, 2021 2 hours ago, Goober said: I need to change those bushings because the steering is still loose. I did get the alignment set, though. RMATV has both the upper steering bushing, and lower steering bearing in stock, i'd advise you to buy them !. 3 Share this post Link to post Share on other sites
Goober 1,555 Posted February 1, 2022 Thanks @shadetreeI finally ordered two sets of steering shaft bearing and bushing. One for each quad. Not really looking forward to the work, but glad parts these are still available. didn’t you have to make your own steering pivot bushes? #7 in photo. I remember you saying you had to make some stuff to tighten up your steering Share this post Link to post Share on other sites
Goober 1,555 Posted February 2, 2022 Oh yeah Shadetree’s guidance was right above my last comment doh Share this post Link to post Share on other sites
_Wilson_™ 6,567 Posted September 13, 2022 On April 12, 2020 at 10:03 AM, jeepwm69 said: I’ve used Novus on Jeep soft top windows. There are different ones depending on the polish needed. One removed the yellowing and light scratches, and another polished. Looks good! @jeepwm69this what i got a few days ago...... As far as the deferent types these 3 are the only ones i could locate BEFORE i purchased my kit. @Goober Thanks tour post i finally have my kit, when ? I'll be able to get around to trying it, Well soon i hope. 2 Share this post Link to post Share on other sites
Goober 1,555 Posted January 28, 2023 (edited) Ok I’m changing the steering bushing and bearing right now. Pretty easy except i need the special bearing nut tool. What do you all use? its like 35mm Edited January 28, 2023 by Goober 1 Share this post Link to post Share on other sites
Melatv 792 Posted January 29, 2023 Hi: What I have used to solve the problem -- is cut a piece of 1/4 flat bar to fit and weld a nut to it. Hope this will help -- also square stock or tube steel will work if you can find the right size. 4 Share this post Link to post Share on other sites
Goober 1,555 Posted January 29, 2023 (edited) Thanks @Melatv i will go to the hardware store tomorrow. Looks like 1-inch bar stock. Thot i have a hitch nut that could fit. super easy job even tho service manual says to pull swing arm 😂 glad i didn’t do that Edited January 29, 2023 by Goober 1 Share this post Link to post Share on other sites
Goober 1,555 Posted January 29, 2023 (edited) 7/8” x 3” bolt and a 7/8-9 castellated nut. i had to take each flat about 150 strokes across a flat bas-tard file. It fits!! now to stake the threads. Edited January 29, 2023 by Goober 5 Share this post Link to post Share on other sites
Melatv 792 Posted January 29, 2023 That good @Goober always something one can come up with to work things out. 1 1 Share this post Link to post Share on other sites